How to Make Your Suno Song Louder
Published · updated · by Loopin
To make a Suno song louder, don’t touch the volume fader: clear the inaudible rumble, fix the balance, then use a limiter to raise it to about −14 LUFS (−11 for rap and pop) with peaks capped at −1 dBTP. That’s the whole trick.
Stop turning up the fader
A raw export’s peaks are usually already close to 0 dBFS. Raising the gain lifts those peaks with everything else, and once they cross the ceiling they clip into harsh distortion. The song gets crunchier, not bigger. That’s the single most common mistake with a quiet Suno song.
A limiter works differently: it holds the loudest peaks at a fixed ceiling and lets the rest of the song come up underneath. That’s where loudness comes from, and it’s the core of every master. If your export is already clipping before you start, read why Suno songs clip on export first.
Free up headroom below 30 Hz
Sub-bass rumble under about 30 Hz is inaudible on phones and most speakers, but it still uses up peak level. High-pass the export at 25–30 Hz and you often gain 1–2 dB of usable loudness before the limiter even starts. Then find any single bass or 808 note that booms louder than the rest and cut it 2 dB at its frequency.
Don’t boost the low end to sound “fuller” before limiting. Every dB added below 100 Hz is a dB the limiter must pull back on every kick, which is how loud masters end up pumping.
Fix mud and harshness before loudness
A limiter makes whatever is there louder, including problems. If the song is muddy at 250–500 Hz or brittle at 4–7 kHz, a 1.5–2 dB cut at each before mastering keeps the louder version clean instead of making it sound squashed and spitty.
Balance first, loudness last. This ordering is responsible for most of the difference between “professionally loud” and “just loud”. The full sequence is in how to master a Suno song.
Pick the loudness target for your genre
About −14 LUFS integrated with a −1 dBTP ceiling is safe everywhere: Spotify, Apple Music and YouTube all turn louder tracks down to around their reference, so going far past it buys nothing on playback. Rap, trap, pop and EDM often sound right at −11 to −10 LUFS. Ballads, acoustic and cinematic songs can sit at −16.
The fastest way to hear the difference: upload the fixed WAV to free online mastering and compare the default (about −14 LUFS) with Punchy (about −11), Club (about −10) and Cinematic (about −16). No account needed.
Judge loudness at matched level
Louder always sounds better for the first few seconds, which is why people overdo it. Use the loudness-matched Original/Mastered A/B: if the master only wins because it’s louder, back off to a gentler feel. Watch for the chorus losing its lift over the verse and the snare losing its snap; both mean too much limiting.
Then compare against a released song in the same style, matched in loudness. If yours still sounds smaller, the gap is balance, not level. Fix it in EQ and run it through the free masterer again.
Frequently asked questions
How do I make my Suno song louder without clipping?
Use a limiter, not the volume fader. High-pass below 30 Hz, fix mud and harshness, then limit to about -14 LUFS with a -1 dBTP ceiling.
How loud should a Suno song be?
About -14 LUFS integrated is safe for all streaming services. Rap, pop and EDM often sit at -11 to -10 LUFS. Keep true peak at -1 dBTP or lower.
Why does my Suno song sound quiet on Spotify?
It's unmastered and sitting below the level of mastered songs around it. A master to about -14 LUFS puts it on equal footing.
Will making my song louder make it sound better on Spotify?
Only up to about -14 LUFS. Beyond that, Spotify turns it down on playback, so extra loudness only costs punch and dynamics.
Is there a free way to make a Suno song louder?
Yes. Loopin's free online mastering needs no account. Pick Punchy (about -11 LUFS) or Club (about -10 LUFS) for louder genres, or the default for about -14 LUFS.
Why does my Suno song pump when I make it louder?
The limiter is reacting to heavy low end. High-pass below 30 Hz, cut any booming bass note by 2 dB, and back the loudness off until the pumping stops.
Should I normalize a Suno song instead of mastering it?
Normalizing only changes volume up to the loudest peak, so it rarely makes a Suno export much louder. A limiter is what raises the average level.